FMS on windows 7? Discussion in '. The issue with the nvidia chipsets usually always boils down to the driver. RC Simulator option - Linux, Mac and Windows: Oct. Esky simulator won't load on. E sky will not load onto windows 7 without error I go through the set up procedure and a. D3D DRIVERS esky fms d3drm dll windows 7. ![]() Posted by on 10 December 2012 06:23 PM First just to make sure: you are running Windows XP & all other programs have been turned off. Please first download 'fmsdisk01.exe' from here. And Be Sure to save that file to your DESKTOP. (Now that the file is completely downloaded onto your desktop. Please Open or Run the 'fmsdisk01.exe' file. This will now install the actual software into your computer system, please install English version (for most people). Once the FMS software is completely installed, you can now run the Flight Module Simulator (FMS) on your computer. Users of New versions of Windows (more recent than WinXP), Please Read Below, otherwise skip that (***) section. ***Setup Instruction for Windows more recent than WinXP*** For those of you who have a more current Windows edition you will need to add a file into the 'FMS' folder in order to successfully run FMS on that Window. If you do not, you WILL get an error message 'missing file d3drm.dll' when you do try to run FMS. So just follow the below instructions and add that file to your FMS folder before you start up the FMS program. The file is located in the mother folder of the link. Go to My computer > C Drive > Program Files > FMS OR Go to Start > Run > C: Program Files FMS OR Go to My computer > C Drive > Program Files (x86) > FMS if you have Windows Vista 64bit. ***Setup Instructions for Windows 8 and Windows 7 64bit.*** Right click on the program, click on properties, go into the compatability tab and select Windows XP. You will need to place a copy of 'D3DRM.DLL' file in the FMS folder, Highlight 'd3drm.dll', Right-Click it and hit 'COPY', move mouse to the FMS folder and Right-Click and hit Paste. A copy should now be in the FMS folder. Launch the Flight Simulator again. ***End Of setup Instruction for Windows more recent than WinXP*** Please first make sure your Transmitter(TX) (either real Transmitter or the fake one) is plugged directly to your computer via USB port. (USB port is much easier to work with & Real Transmitter needs Power Light ON to Operate on computer, the Fake remote does not need any battery to operate.) Once the remote is plugged in, now please run the Flight Module Simulator (FMS) via the Short Cut. For every new installation of the FMS you will always need to configure the FMS program to 'correctly' accept commands from the transmitter(TX), so that the controls / buttons work EXACTLY like they would on a real R/C Helicopter or R/C Plane. To configure the FMS program to your Transmitter(TX), Please follow the Below pictures & instructions. 1) So FMS is installed on your computer, Open or Run the FMS program and this Screen will appear. Notice Top Row contains all the commands for configuring / Editing this software. Please Go to ' Controls' & then ' Analog Control'. 2) A box will appear, Please Highlight ' Joystick Interface'. 3) Under ' Joystick Interface', please first Click on ' Resources' to check to see if your Computer Recognizes the Transmitter(TX) Remote that should be plugged into your computer via a USB port. 4) Once you click on ' Resources', This screen will pop up. It will display information under ' Joystick 1' and ' Joystick 2'. Underneath our above picture ' Joystick 1' says ' Microsoft PC-joystick driver' which is a CONFIRMED SUCCESS. This means your computer is able to read the TX Remote that is Plugged into the Computer. As long as the ' Microsoft PC-joystick driver' message is there along with 6 blue/white bars, either under Joystick 1 or Joystick 2, means Success. Please hit ' Ok' button to get back to previous menu. (**things to try if you are not getting the right message: try unplugging all other game devices/remotes from your computer [leaving your mouse & keyboard plugged in], try using various USB ports to plug into, try using other TX remotes on FMS, etc.) 5) Now click on ' Mapping / Calibration'. The screen that pops up is the HEART & SOUL of configuring FMS to the TX remote. STEP ONE: Please Make Sure to set the Numbers & Check the boxes the way you see it here. Under ' Channel' column the numbers should read '4,2,1,3, 4,2,1,3,' TOP going DOWN and all the Boxes under the ' Inv' column should be Checked.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
January 2019
Categories |